How to make a Design Wall

 

IMG_3674

 

Supplies:

→One sheet of foam insulation board. I bought this at Home Depot for $12. It measures 4′ x 8′ x 1/2″.

IMG_3667

The foam insulation board actually consists of a 1/2″ piece of foam with a paper layer on both sides. The back side of this board is a metallic paper. These foam boards can look different or even be just foam. Doesn’t really matter because we are covering it up any way.

IMG_3679

→A vinyl Design Wall by Fons & Porter or If you want to save even more you can use the back side of any vinyl tablecloth(no grid lines- no big deal).

I bought this at Joann’s for $25 then used their 50% off coupon so it was only $12.50. They have a 50% or 40% coupon every week.

fonsandporterdesignwall

→Binder clips, about 12 will do. I didn’t price these, but they are very inexpensive and I figure most of us have some laying around anyway.

IMG_3681

How to assemble:

1. Center and stretch the pre-packaged design wall or vinyl tablecloth onto the foam board. Smooth out any wrinkles to make as flat as possible. Leave excess foam board all at one end.

Tip: If your vinyl design wall or tablecloth is wrinkled…do not iron it! Just stretch it out and let it relax naturally. You can see on my board that I have a few “bubbles” in my wall. I got a little too happy with the iron trying to steam out the wrinkles. These spots are not a problem, but best if avoided all together!

 

IMG_3664

2. Lay foam board flat on the floor and using your longest ruler(6 x 24 here) line it up with the end of the design wall where you want to remove the excess foam board.Here you need to decide how much board you want to leave at the bottom.

Things that may affect where you trim your board:

how you are going to use your design wall– horizontally or vertically.

I am using mine vertically and didn’t want the design area touching the floor. If horizontal, you may want a small area left on each end for mounting or none at all.

will your design wall be movable– fixed to a wall or movable from room to room.

I want mine to be able to move to where ever I am sewing at- kitchen, sewing room or I can break it down and take it to a guild meeting.

your height– I am short so I left only 2″ at the bottom.

IMG_3647

3. Using your rotary cutter, gently press the blade through the top layer of paper on the foam board and work your way across the board.

Be careful not to go through to the other side here!!!

IMG_3654

4. Gently snap the foam board, leaving the paper backing still intact.

IMG_3657

5. Using a pair of scissors or an x-acto knife/box cutter to slice through the paper backing.

IMG_3658

IMG_3662

and Voila!

You can save that small piece for another project or make a mini design wall using leftover batting or flannel to cover it.

IMG_3675

Here is mine in action.

I have to say I am head over heels in love with it! It is so light and portable. I can just bring it in the living room with me while I am sewing at the kitchen table and easily take it back to my sewing room when I’m done:) Because it is so light it should be no problem to attach it to a wall if you like. Some simple hooks or Command strips will do the trick if your real classy and don’t want to put any nail holes in the wall:)

No need for a giant empty wall to get your design on!

Sassy indeed

Share Button
Print Friendly, PDF & Email

Comments

  1. I made my design wall the other day, and it’s already being put to good use.

  2. Maurine Reynolds says:

    How is it free standing, or is it leaning against something ,I need it portable but free standing.

  3. a6b6qw

Trackbacks

  1. […] is a nice tutorial: How to make a design wall Reply With […]

  2. […] Design Wall Tutorial at The Sassy Quilter Blog […]

  3. […] How to make a Design Wall […]

Speak Your Mind

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.